Mtd E740F Instrukcja Użytkownika

OPERATOR’S MANUALPRINTED IN U.S.A.FORM NO. 770-10004C.fm(6/00)IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022

10Figure 12Shift Lever The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel

11Track Lock LeverThe track lock lever is located on the right side of the snow thrower and is used to select the position of the auger housing and th

12• Connect power cord to switch box on engine. Plug the other end of power cord into a three-hole, grounded 120 volt AC receptacle.• Push starter but

13SECTION 6: MAKING ADJUSTMENTWARNING: NEVER attempt to make anyadjustments while the engine is running,except where specified in the operator’smanua

14• Place the shift lever into the sixth (6) position.• Rotate the shift arm clockwise (from the operator’s position) as far as it will go.• Thread th

15Gear CaseThe gear case is lubricated with grease at the factory and does not require checking. If disassembled for any reason, lubricate with 2 ounc

16• Unhook the idler spring from the hex bolt on the auger housing. See Figure 21.• Back out the stop bolt until the support bracket rests on the auge

17Figure 23Off-season StorageWARNING: Never store the machine orfuel container indoors where there is anopen flame, spark, or pilot light such as onwa

18SECTION 9: TROUBLESHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in the ON p

19Model E740FRef. No.Part No. Part Description1. 618-0123 RH Housing2. 618-0124 LH Housing 3. 710-0642 Self Tapping Screw, 1/4-20 x .754. 711-0909A Sp

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Contents of Hardwa

20Model E740F11223345671891031113121431516171819201819202121222324252627282930313233343520363738404135204344452726464747484950265152535454555657585960

21Model E740FRef.No.PartNo. Description1. 714-0507 Cotter Pin2. 747-0877 Rod3. 710-0599 Hex Washer Screw 1/4-20 x .54. 784-5680 Handle Support Bracket

22Model E740F1234567891011121415131610212223252322261827281330313233161835343637383941404217403929249191816434413

23Model E740FRef. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632A Auger Idler Arm4. 710-0459A Hex Cap S

24Model E740F25192627242322211617181920293031232323430227261925362124232212 23010181920211311141593765432403938323728835

25Model E740FRef. No.Part No. Part Description1. 784-5648 Frame Cover2. 710-1652 Tap Screw 1/4-20 x .6253. 748-0190 Spacer .508 ID x .75 OD 4. 732-026

26Model E740F12631012785491315141716192022222019282118211815131429313230323437383623352739114041424443455146474852465351545554501617493756562425262633

27Model E740FRef. No.Part No. Part Description1. 720-0223 Grip2. 710-0604 Tap Screw, 5/16-18 x .6253. 784-5642 Track Lockout Plate4. 710-0157 Hex Cap

28Model E740F1123456748910111213141516171819191616162021222324252627

29Model E740FRef. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x .6252. 731-1324 Belt Cover3. 732-0710 Extension Spring4. 710-0627

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th

30Notes

31

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchandisepurchased

43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with

5SECTION 2: CONTENTS OF HARDWARE PACKLay out the hardware according to the illustration for identification purposes. Part numbers are shown inparent

6SECTION 3: ASSEMBLING YOUR SNOW THROWERNOTE: Reference to right or left side of the snowthrower can be determined from behind the unit in theoperat

7Attaching Chute Directional Control(Hardware C)• Thread one hex nut about halfway onto eye bolt on the chute directional control. Insert eye bolt thr

8• Make certain to check for correct adjustment of the shift rod as instructed in the Final Adjustment section before operating the snow thrower.Attac

9IMPORTANT: It is NOT recommended that this snow thrower be operated on a gravel surface, as loose stones can be easily picked up and thrown by the ma