Mtd E663G Instrukcja Użytkownika

IMPORTANT: Read safety rules and instructions carefully before operating equipment.ModelE663GPRINTED IN U.S.A.Warning:This unit is equipped with an in

10SECTION 6: MAKING ADJUSTMENTSWARNING: NEVER attempt to clean chuteor make any adjustments while engine isrunning.Chute Assembly AdjustmentThe dista

11If adjustment is necessary:• Loosen the jam nut on the traction drive cable andthread the cable in or out as necessary.• Retighten the jam nut to se

12SECTION 7: MAINTAINING YOUR SNOW THROWERLubricationWARNING: Disconnect the spark plug wireand ground against the engine beforeperforming any mainte

13SECTION 8: SERVICEWARNING: Disconnect the spark plug wireand ground against the engine beforeperforming any repairs or maintenance.EngineRefer to t

14Drive Belt• Follow the first four steps of the instructions forservicing the auger belts.• Pull idler pulley up, and lift belt off engine pulley and

15SECTION 9: OFF-SEASON STORAGEWARNING: Never store engine with fuel intank indoors or in poorly ventilated areas,where fuel fumes may reach an openf

16SECTION 10: TROUBLESHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in ON posi

17Ref.No.Part No. Part Description1.618-0123 RH Housing2.618-0124 LH Housing3.710-0642 Self Tapping Screw, 1/4-20 x .754.711-0910 Spiral Axle, 28”5.71

18Model 66311234455647789101112151314151617181192021222324252526282926113031323334835Drive ClutchCableAuger ClutchCableAuger ClutchCableBlowerHousing3

19Model 663Ref.No.Part No. Part Description1.710-1652 Hex Screw2.784-5688 Drive Cable Guide Bracket3.784-5687 Auger Clutch Cable Bracket4.756-0625 Rol

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Loose Parts...

20Model 66312345678910111214151316109 1819202122231325232226182728133030313231323316183534363738394140421740392924

21Model 663Ref.No.Part No. Part Description1.712-0116 Lock Jam Nut 3/8-242.756-0178 Flat Idler3.784-5632A Auger Idler Arm4.710-0459A Hex Cap Screw 3/8

22Model 66312345674891011121315141617181920161621222324252627

23Model 663IMPORTANT: For a proper working machine, use FactoryApproved Parts.V-BELTS are specially designed to engage and disengagesafely. A substitu

24Model 6639232924126281871220621155418112712204435324845353233444546496536385132114142434342411169473140343760522261555657868131064671970393912172152

25Model 663Ref.No.Part No. Part Description1.684-0008A Shift Arm Assembly2.684-0022 Chute Crank Ass’y3.715-0138 Rolled Pin4.710-0262 Carriage Bolt, 5/

26

27

MANUFACTURER’SLIMITED WARRANTYThe limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchandisepurchased and us

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis Warning symbol points out important safety instructions which, if not followed, could endanger the

4• When cleaning, repairing, or inspecting, makecertain the auger, impeller and all moving partshave stopped. Disconnect spark plug wire and keepaway

5SECTION 2: LOOSE PARTS The snow thrower is shipped with following loose parts in the carton. Please remove all loose parts from the cartonbefore dis

6NOTE:If the connector is not properly assembled, theshift rod will pivot and you will not be able to changespeeds or change directions.• Unwrap the h

7b. Engage the traction control, and attempt tomove them machine both forward andrearward. You should experience resistanceas the wheels should not be

8Fuel Shut-off ValveThe fuel shut-off valve, locatedunder fuel tank, controls fuel flowfrom the tank. Always make certainit is in the Open (vertical)

9• Electric Start: Do NOT prime engine. Push starterbutton on top of the engine to crank the engine.When engine starts, release starter button.• Recoi