Mtd 614E Instrukcja Użytkownika

Snow ThrowerModels 614E, 644E, 664GOperator’s ManualModel 664 ShownIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD LLC, P.O. BOX 361131 CLE

10Attaching The Chute Directional Control (Hardware C)• Thread one hex nut about halfway onto eye bolt on the chute directional control. • Insert eye

11If your unit is not equipped with a lamp, contact Customer Support as instructed on page 2 for information regarding price and availability.Snow Thr

12• Crank clockwise to discharge to the left.• Crank counterclockwise to discharge to the right.Clean-Out ToolWARNING: Never use your hand toclear a

13WARNING: The optional electric starteris equipped with a grounded three-wirepower cord and plug, and is designed tooperate on 120 volt AC household

14Check the adjustment of the auger control as follows:• When the auger control is released and in the disengaged “up” position, the cable should have

15WARNING: The muffler, engine, and theirsurrounding areas become hot and cancause a burn. Do not touch.• Discharge snow downwind whenever possible. S

16• With the traction control is engaged, the friction wheel must contact the drive plate. See Figure 20.Figure 20If adjustment is necessary: • Loosen

17NOTE: Make certain to check for correct adjustmentof the shift rod as instructed in the Final Adjustmentssection before operating the snow thrower.D

18Auger Shaft• At least once a season, remove shear bolts on auger shaft. Oil or spray lubricant inside shaft and lubricate the auger bearings. See Fi

19Augers• The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a hard foreign object or ice jam, the snow thr

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Hardware Pack...

20Drive Belt• Follow first four steps of previous instructions.• Pull idler pulley up, and lift belt off engine pulley and friction wheel disc. See Fi

21• Run engine until fuel tank is empty and engine stops due to lack of fuel.• Drain carburetor by pressing upward on bowl drain, located below the ca

22SECTION 10: MODELS 614E, 644E, & 664G4213567810111213814151617718187192021166222313136724616262728252930313233343637333232333537363332313063839

23Models 614E, 644E, & 664GREF.NO.PARTNO. DESCRIPTION1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm4. 710-0459

24Models 614E, 644E, & 664G12345789561516161718181919202021225354252627282930532334352336385439404139424344454617141373710122467555557†58†59†47††4

25Models 614E, 644E, & 664GREF.NO.PARTNO. DESCRIPTION1. 712-0116 Jam Lock Nut 3/8-242. 732-0193 Compression Spring3. 736-0105 Bell Washer4. 784-56

26Models 614E, 644E, & 664G11234455616” Wheels13” or 15” Wheels47789101011111241513141516171811920212223242526282941413031323334835Drive ClutchCab

27Models 614E, 644E, & 664GREF.NO.PARTNO. DESCRIPTION1. 710-0599 Hex Screw 2. 784-5688 Drive Cable Guide Bracket3. 784-5687A Auger Clutch Cable Br

28Models 614EREF.NO.PARTNO. DESCRIPTION1. 710-1652 Hex Washer Screw 1/4-20 x.52. 731-1324 Belt Cover3. 732-0339 Extension Spring4. 710-0627 Hex Screw

29Models 644E & 664GREF.NO.PARTNO. DESCRIPTION1. 710-1652 Hex Washer Screw 1/4-20 x.502. 731-1324 Belt Cover3. 710-3005 Hex Cap Screw 3/8-16 x 1.2

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the persona

30REF.NO.PARTNO. DESCRIPTION1. 618-0123 Housing—R.H.2. 618-0124 Housing—L.H.3. 710-0642 Hex Screw 1/4-20 x.754. 711-0908A Spiral Axle 24"711-0910

31NOTES

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the

45. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate

5SECTION 2: CONTENTS OF HARDWARE PACK (Boxed Units)Lay out the hardware according to the illustration below for identification purposes. Part numbers

6SECTION 3: ASSEMBLING YOUR SNOW THROWERNOTE: References to right or left side of the snowthrower are determined from behind the unit in theoperating

7Assembly (Crated Unit)WARNING: Disconnect the spark plugwire and ground it against the engine toprevent unintended starting.• Remove the lower two p

8• Insert curved end of the Z fitting into the top hole in the triangular metal tab on the auger control grip. The triangular metal tab on the auger c

9• Thread the ferrule onto the shift rod, up or down the shift rod and align with the far hole on the narrow side of the shift lever assembly behind t