Mtd 315-860-000 Instrukcja Użytkownika

.75OUTDOOR POWER EQUIPMENT for all seasonsVImportant:Read Safety Rules and Instructions Carefully26" and 33" SNOW THROWERSModel Numbers 315-

FIGURE 19.FIGURE 20.Throttle Control (See figures 18 and 20)The throttle control is located on the righ hand side of the handle panel. It

NOTEAdditional priming may be required (for initial start only) if temperature is below 15° F.3. Grasp the starter rope handle and pul

SKID SHOE ADJUSTMENTThe space between the shave plate aid the ground can be adjusted for close snow removal by placing skid shoes in

DRIVE WHEELS (Models 860 and 960)Snow throwers model 860 and 960 are equipped with a differential which makes the unit easy to maneuver

LUBRICATIONSPECIFICATIONS:Lubricate once a season or after every 25 h 3urs of operation.Oil—Use SAE 30 or equivalent.Grease—Use automotive multi-purpo

MAINTENANCEAUGERSThe augers are secured to the spiral shaft with two hex boits and hex lock nuts (see Ref. Nos. 40 and 50 on page

EnginePulleyAugerDriveBeltFIGURE 28.5. Remove the top screws and lock washers which attach the auger housing asserr bly to the frame a

FIGURE 32.c. Remove drive belt from the engine pulley and bottom drive pulley.d. Replace belt and reassemble in reverse order.9. Reassemble the two

FIGURE 34.8. Replace the rear cover.ACAUTIONCheck engine and snow thrower frequently for loose nuts, bolts, etc. and keep these items tight

Trouble Shooting ChartProblemPossible Cause(s)SolutionEngine fails to start1. Check fuel tank for gas.2. Key not in switch on engine.3. Spark plug

INDEXSafe Operation Practices...3Assembly Instructions...

Models 800,860 and 960IF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODEL20

Models 800,860 and 960PARTS LIST FOR MODELS 800, 860 AND 960 SNOW THROWERSREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONN

Models 800,860 and 960IMPORTANTBelts listed by Part Number are of special construction and siould be used when replacement is necessary

Models 800,860 and 960PARTS LIST FOR MODELS 800, 860 AND 960 SNOW THROWERSREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONN

Models 800,860 and 960Gearcase lubricant—4 oz. of Shell Alvania grease, part number 737-0168.AUGER HOUSING24

Models 800, 860 and 960PARTS LIST FOR MODELS}00, 860 AND 960 SNOW THROWERSREF. PARTCOLORNEW REF.PART COLORNEWNO. NO. CODEDESCRIPTIONPARTNO.NO.CODEDESC

Model 80093 ,90GEAR CASE BREAKDOWN26

Model 800PARTS LIST FOR MODEL 800 SNOW THROWER1EF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART1 05487 —452Frame Ass’

Models 860 and 9(30.9093 9i‘NOTE:If these parts are to be disassembled for any reason, it is necessary to heat them after driving th

Models 860 and 960PARTS LIST FOR MODEL 860 AND 960SNOW 1rHROWEF tslEF.MO.PARTNO.COLORCODEDESCRIPTIONNEWPARTREF.NO.PARTNO.COLORCODEDESCRIPTIONNEWPART10

ACWARNINGTo reduce the potential for any injury, comply with the following safety instructions. Failure to complywith the instructions may result in p

PARTÍ) INFORMATIONPOWER EQUIPMENT PARTS AND SERVICEParts and service are available through the authorized .'.ervice firms listed below.

NOTEThis owner’s manual covers various models of snow throwers. The uni illustrated may be different thar your unit.NOTEThis unit is s

Hex Bolt (A) Belleville Washer (B)4.5.Slide the slotted end of the handles under the belleville washers on the self-tapping screws which

11. Place hex bushing (I) into bracket beside the chute assembly. Position the hex bushing so the hole in the bushing is close to the ch

15. Place the shift rod through the slot in the bottom frame cover. Thread rod into ferrule. See figure 10.FIGURE 10.16. Move the

18. Secure with belleville washer (B) (cupped side goes against shift lever), compression spring (L) and elastic lock nut (M). See f

21. Swing the left hand lockout rod down and simply hold it beside the drive bracket. Do not pull on spring. Do not move bracket