Mtd 219-405-000 Instrukcja Użytkownika

$1.00OWNER'S GUIDEASSEMBLY • OPERATION • MAINTENANCE • PARTSREAR TINE TILLERModel Number 219-405-000Important: Read Safety Rules and Instructions

AdjustmentFIGURE 17.BELT TENSION ADJUSTMENT—Drive and Tii le ClutchesPeriodic adjustment of the belt tension may be reqi lired due to normal stretch a

Wheels—Lubricate the wheel bearings with a iight oil after each fifteen hours of operation.Tine and Wheel Drive Controls—Lubricate the pivot points on

Tine BeltSetScrewsFIGURE 21._^e>Rear Engine Pulley H(x Bdt4. Loosen, but do not remove, the hex bolt on the rear engine pulley. See figure 22.5.

NOTEUpon reassembly, refer to illustration on page 18 for correct assembly of wire belt guard for your model tiller.HubFIGURE 26.NOTEIf th

Trouble Shooting GuideTroublePossible Cause(! i)Corrective ActionEngine fails to start1. Fuel tank empty, or stale fuel.1. Fill tank with clean, fresh

NOTES15

Model 4050^'Specifications subject to change without notice or obiigatior^________16

Model 405PARTS LIST FOR MODEL 405 ROTARY TILLERHEF.NO.PARTNO.CODEDESCRIPTIONREF.NO.PARTNO.CODEDESCRIPTION1710-0528Hex Bolt 5/16-18 X 1V4" Lg.*48

Model 405NOTE: The engine is not under warranty by the tilier manufacturer.. .if repairs or service is needed on the engine, please contact your neare

Model 405PARTS LIST FOR MODEL 405 ROTARY TILLERtEF.»JO.PARTNO.CODEDESCRIPTIONREF.NO.PARTNO.CODE DESCRIPTION1 746-0484Clutch Control Cable55 736-0270Be

INDEXSafe Operation Practices...3Assembly...

Model 405TINE CHAIN CASE 14981Note: Use 10 ounces of Plastilube #0 grease. Order Part No. 737-0133.PARTS LIST FOR MODEL 405 TILLER CHAIN CASE 14981 (T

Model 405WHEEL CHAIN CASE 1697628 29NOTE: Use 12 ounces of Plastilube #0 grease. Order Part No. 737-0133.PARTS LIST FOR MODEL 405 TILLER CHAIN CASE (W

Heavy Duty Rear Tine Garden Tiller Attachments Availab le for All-Season Use31-011031-014431-01458" F jrrower Opener“V”-3ar Cultivating Kit (Must

PARTS INFORMATIONPOWER EQUIPMENT PARTS AND SERVICEParts and service are available through the authorized service fir ns listed belovr. All orders shou

Ac WARNING \To reduce the potential for any injury, comply with the following safety instructions. Failure to comply with the instructions may result

ASSEMBLYo---^NOTEThis unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil

Flat2. Insert clevis pin (D) through the tine shield and depth bar assemblies. Secure with hairpin clip (E).—See figure 4.3. Insert hex bolt (A) int

Belleville Washers (G)FIGURE 7.2. Place handle assembly in position on the tiller. Working on one side of the unit, insert one hex bolt (F) through b

Control WireHole in Clutch LeverFIGURE 10.Cable Ties (L)FIGURE 11.1. Remove one nut and the lock washer from the end of the drive clutch cable (short

OPERATION-NOTEEngine is shipped without oil.BEFORE STARTING1. Before operating tiller for the first time or if ines have been removed and reassembled

AWARNING IDo not push down on the handles so that the wheels are lifted off the ground while the tine clutch is engaged, or the tiller could move